Heating Repair · South Florida
Heating repair in South Florida when the heat will not come on
Heat strips, heat pump heating mode and thermostat settings checked and repaired.
Atención en español en todo el sur de Florida.
- Duct sealing
- Commercial HVAC
- Ductwork
- Financing available
- AC installation
- Dehumidifiers
- Heat pumps
- Indoor air quality
- Smart thermostats
- AC repair
- Rooftop units
- Se habla español
- Mini-split AC
- Air duct cleaning
Heating Repair
What it covers
On heat pumps, the work can include the outdoor unit, the reversing valve signal, and the heating mode the system uses when it changes from cooling to heating. Some systems also use heat strips, and those can have a failed relay, a bad limit switch, or loose wiring that keeps them from turning on. We also check for a tripped breaker, a dirty filter, or a thermostat that is set to cooling when you expect heat. A thermostat set to auto can help show whether the system is calling for heat or only moving air.
What we check
What we check
When the heat will not come on, we start at the thermostat and check the setting, mode, fan choice, and temperature call. A wrong setting can keep the system from asking for heat at all. Then we look at the air handler, breakers, service switch, and wiring for loose connections or a tripped safety. On heat pump systems, we also check whether the unit is set to heating mode and whether the reversing valve is being asked to move.
Inside the unit, we test the heat strips, relays, contactors, and limit switches because each one controls how electric heat comes on and stays on. A bad strip or a failed relay can leave you with cool air or weak heat. We also check filters and airflow, since blocked air can make the heater shut down early. For homes and businesses, we verify the thermostat wires at the base plate and compare the heat setting to the room temperature. We also check whether the fan is set to Auto instead of On.
Heating Repair
Choices to make
When heat will not come on, the choice can start with the thermostat, the air handler, or the heat pump itself. We check the heating setting, the fan setting, the batteries if there are any, and the set point against the room temperature. Then we look at heat strips, relays, contactors, breakers, and wiring, because a failed part can make a repair the better choice than replacing the whole system. If the thermostat never sends a heat call, the control wires and subbase need a close look.
A repair can make sense when one part has failed and the cabinet, blower, and duct connection are still solid. Replacement may come up when the heat pump no longer holds heating mode well, the heat strips are damaged, or several controls and motors are tied to the same problem. Age, corrosion, rusted drain pans, and repeated shutdowns all matter in that choice for homes and businesses. Check whether the outdoor coil is clear, because packed leaves or lint can change how the system heats.
Heating Repair
After the work
After the visit, you are left with a clear picture of what kept the heat from coming on and what parts were checked. We look at the thermostat heating setting, the fan setting, the breaker, the air handler, the heat strips, and the heat pump heating mode if your system uses one. If a loose wire, bad relay, dirty contact, or control issue showed up, we note it and repair what we can reach. The thermostat should be left on Heat before you change the temperature.
To keep the system in good shape, keep the indoor filter clean and make sure supply and return grilles stay open. If the thermostat screen goes blank, the setting keeps changing, or the system calls for heat but sends cool air, those are signs to check again. For heat pumps, do not switch between heating and cooling too often, and leave the outdoor unit clear of leaves and boxes. Check the thermostat batteries if the display is weak or flickers.
How it works
One call. No runaround.
One call
Call or message the same number. Se habla español.
A real diagnosis
We check the parts, not just the thermostat, and tell you what we found.
Your call
Repair or replace is your decision, with honest answers to make it.
Where
Heating Repair from Miami to West Palm Beach
Questions
Heating Repair: common questions
Why does my heat stay off even though the thermostat says heat is on?
We check the thermostat call for heat, the air handler, and the safety switches that can stop the system from starting. A loose wire, a tripped breaker, or a setting change can keep the heat from coming on. We also look at whether the indoor fan is being told to run and whether the control board is reading the heat request correctly.
My house gets cool air when the heat strips should be running. What could that mean?
Heat strips add electric heat inside the air handler, so we look at the strip elements, relays, wiring, and the controls that tell them to energize. If one part is not pulling in, the system may blow air that feels cool or only mildly warm. We also check the blower operation, since air movement and strip heat have to work together.
I switched my heat pump to heat, but the air still feels cold at the vents. What should I know?
With a heat pump, the outdoor unit and the indoor system have to switch into heating mode together. We check the reversing valve signal, the thermostat settings, and the auxiliary heat call. If the unit is in a defrost cycle, the air can feel different for a short time. We also look at the supply and return airflow through the ductwork.
I changed the thermostat to heat, but it still seems to follow the old cooling setting. Why is that?
We look at the thermostat mode, fan setting, temperature swing, and whether the screen is actually sending a heat demand. Sometimes the thermostat is set to cool, fan on, or auto in a way that changes how the system responds. We also check the wiring at the thermostat base and the low-voltage signal back to the equipment.
My system clicks, but I only get lukewarm air from the registers. What parts do you check first?
First, we inspect the relay, contactor, and heating components that turn on the warm air path. Then we look at the ductwork for leaks, blocked returns, and closed dampers that can affect how heat moves through the home. If the system uses emergency heat, we also check whether that setting is being called correctly and whether the indoor unit is matching the demand.
Call Torres — we respond right away.
Miami-Dade, Broward and Palm Beach. Se habla español.
Prefer to write? Send the form and we call you back.